Your Plumbing Crash Course: A Necessity for Installing a Bathtub
Your Plumbing Crash Course: A Necessity for Installing a Bathtub
Blog Article
They are making several good observations on the subject of How to Install a Bathtub overall in the article beneath.
Mounting a bathtub isn't exactly rocket science, but it does require solid plumbing, woodworking, and also sometimes, tiling skills. Changing an old tub with a new one is additionally a reasonably challenging task. If the old tub is conveniently available, the task can move easily; if you need to open a wall surface to eliminate the old bathtub as well as place the new tub, the job is a lot harder. In either case, the project is within a house handyman's skills, although you will certainly require an assistant to vacate the old bathtub and also set in the new one. Make certain you have actually certified on your own for the task as well as fit attempting it. Instead of employing a specialist to take over a halfway-completed job, it is better to take into consideration using one prior to you begin. Chances are you may require a specialist plumber to make tube connections.
This article will help you set up a new bathtub in your bathroom if you have already bought a new bathtub and do not need to transform the arrangement of your previous water supply pipelines.
Your devices as well as product checklist must comprise the following:
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your installment, after that the first thing you should do is disconnect the supply of water. After doing so, switch on the faucets to drain pipes any kind of water continuing to be in the system. The procedure of getting rid of the existing taps can be rather troublesome as a result of the limited accessibility that is frequently the case.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the faucets. Have a fabric prepared for the staying water that will come from the pipelines. When the supply pipelines have actually been eliminated, use the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary taps from transforming throughout this procedure. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any old securing compound.
Prior to moving on to fit the brand-new faucets, compare the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Suitable New Touches
If the tails of the new taps are plastic, then you will certainly require a plastic port to stop damages to the string. One end of the connector fits on the plastic tail of the faucet and the various other end provides a connection to the current supply pipelines.
If you need to fit a monobloc, then you will certainly call for minimizing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, place the tap in the mounting hole in the bath/basin making sure that the washing machines are in location between the faucet and also the sink. Secure the tap in position with the manufacturer offered backnut. As soon as the tap is safely in place, the supply pipes can be connected to the tails of the taps. The taps can either be attached by using corrugated copper piping or with normal faucet adapters. The previous type needs to be linked to the tap finishes first, tightening only by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.
Installing the Tub
Utilizing both wood boards under its feet, place the bathtub in the needed placement. The wood boards are helpful in evenly spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto four little points.
The following goal is to guarantee that the bath tub is leveled all round. This can be accomplished by examining the spirit level and also changing the feet on the bath tub up until the spirit level checks out degree.
To install faucets, fit all-time low of the outermost flexible faucet adapter to the ideal supply pipeline by making a compression sign up with; then do the exact same for the other faucet.
Activate the supply of water and also examine all joints and new pipework for leakages and tighten them if needed. Load the bathtub as well as also inspect the overflow outlet as well as the normal electrical outlet for leaks.
Lastly, deal with the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and also securing around the bath tub needs to wait up until the bathtub has actually been made use of a minimum of when as this will resolve it into its last setting.
Preparing for the Installment
To start with, the supporting framework supplied with the bathroom ought to be fitted (if required) according to the supplier's guidelines. Next, fit the taps or mixer to the bath tub. When fitting the tap block, it is necessary to make certain that if the faucet comes with a plastic washing machine, it is fitted in between the bathroom and the faucets. On a plastic bath, it is also reasonable to fit a supporting plate under the faucets device to prevent stress on the bathtub.
Fit the versatile tap adapters to the bottom of the two taps using 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you utilize every one of the provided washing machines.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath should currently prepare to be fitted in its final position.
Tiling Around the Bathtub
In the area where the bathroom fulfills the floor tile, it is essential to seal the accompanies a silicone rubber caulking. This is essential as the installation can relocate sufficient to fracture an inflexible seal, triggering the water to permeate the wall between the bathroom and also the tiling, causing issues with dampness and possible leakages to the ceiling listed below.
You can select from a selection of coloured sealants to blend in your components and fittings. They are offered in tubes and also cartridges, and are capable of securing voids up to a width of 3mm (1/8 inch). If you have a larger space to load, you can load it with spins of drenched paper or soft rope. Remember to always fill the tub with water before sealing, to enable the motion experienced when the tub is in use. The sealant can crack fairly very early if you do not take into account this movement prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally quickly available on the marketplace. It is a good idea to fit the ceramic tiles using water-resistant or water-proof glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you enjoy reading up on A Step-by-Step Guide to Installing a Bathtub? Write a review further down. We would be pleased to see your responses about this content. We hope that you come back again later on. For those who liked our page please remember to pass it around. Thank you for taking the time to read it.
Maintenance Sign-Up Report this page